Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2445 | Manualshive

Страница: 2445 / 2589

background image

Fig. 11: Identifying Windshield Washer Motor Remove/Install Components

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

WINDSHIELD WASHER MOTOR INSPECTION

1. Connect battery positive voltage to windshield washer motor terminal A and terminal B to ground.
2. Verify that the windshield washer motor operates normally.

z

If there is any malfunction, replace the windshield washer motor.

Fig. 12: Identifying Windshield Washer Motor Terminals

Courtesy of MAZDA MOTORS CORP.

WINDSHIELD WASHER NOZZLE REMOVAL/INSTALLATION

1. Remove the windshield wiper arm and blade. (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

.)

2. Remove the cowl grille. (See

COWL GRILLE REMOVAL/INSTALLATION

.)

3. Remove the windshield washer hose from the windshield washer nozzle.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 10

© 2005 Mitchell Repair Information Company, LLC.

«
...
2443
2444
2445
2446
2447
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: B-Speech Страницы: 18

Бренд: JASTEC Страницы: 12

Бренд: Code 3 Страницы: 8

Бренд: CITROEN Страницы: 52

Бренд: AC Schnitzer Страницы: 16

Бренд: Saab Страницы: 288

Бренд: Sunsky Страницы: 9

Бренд: Metra Electronics Страницы: 2

Бренд: M7 SPEED Страницы: 6

STO N SHO SNS 144

Бренд: Big Mikes Performance Parts Страницы: 7

Бренд: Lincoln Страницы: 10

Бренд: Mobility Networks Страницы: 52

84 61 0 028 926

Бренд: BMW Страницы: 13

Бренд: Roadtrek Страницы: 61

Бренд: Jaeger Страницы: 11

Бренд: ATS Страницы: 12

Бренд: Opel Страницы: 242

Бренд: Whelen Engineering Company Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды