Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1666

Страница: 1666 / 2589

AWD

Fig. 30: Identifying Fuel Pump Unit, Quick Release Connector, Service Hole Cover & Torque
Specifications (AWD)

Courtesy of MAZDA MOTORS CORP.

FUEL PUMP UNIT DISASSEMBLY/ASSEMBLY [MZI-3.7]

1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.

Fig. 31: Identifying Fuel Filter Body, Pressure Regulator, O-Ring & Fuel Pump

Courtesy of MAZDA MOTORS CORP.

FUEL PUMP UNIT INSPECTION [MZI-3.7]

CAUTION:

It is normal to hear the fuel pump operating when the ignition switch

2008 Mazda CX-9 Grand Touring

2008 ENGINE Fuel System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:00:01 AM

Page 25

«
...
1664
1665
1666
1667
1668
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды