Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 92

Страница: 92 / 2589

DO NOT RECUR AFTER REPAIR

Turn the ignition switch to LOCK position.

Disconnect the negative battery cable and wait

for

1 min or more.

Connect all SAS control module connectors.

Connect the driver and passenger-side pre-
tensioner seat belt connectors.

Connect the driver and passenger-side curtain air

bag module connectors.

Connect the driver and passenger-side front seat
connectors.

Connect the passenger-side air bag module

connector.

Connect the clock spring connector.

Connect the instrument cluster connector.

Connect the negative battery cable.

Turn the ignition switch to ON position.

Does the air bag system warning light operate

properly?

Yes

Complete troubleshooting, then
explain repairs to customer.

Recheck malfunction symptoms, then

repeat from Step 1 if malfunction

recurs.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Symptom Troubleshooting (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:17:14 AM

Page 9

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды