Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2387

Страница: 2387 / 2589

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Inner sail garnish (See

INNER SAIL GARNISH REMOVAL/INSTALLATION

2. Rear door trim (See

REAR DOOR TRIM REMOVAL/INSTALLATION

3. Rear door speaker (See

REAR DOOR SPEAKER REMOVAL/INSTALLATION

4. Rear door glass (See

REAR DOOR GLASS REMOVAL/INSTALLATION

5. Power window motor (See

POWER WINDOW MOTOR REMOVAL/INSTALLATION

3. Remove the nuts.

Fig. 12: Identifying Rear Power Window Regulator Nuts & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Insert a hand through the speaker installation hole, rotate the drum housing in the direction shown in the

figure to detach the tabs from the rear door unit.

Fig. 13: Rotating Drum Housing

Courtesy of MAZDA MOTORS CORP.

5. Move the rear power window regulator in the direction of the arrow and remove it.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 8

«
...
2385
2386
2387
2388
2389
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды