Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 535 | Manualshive

Страница: 535 / 2589

background image

Fig. 24: Locating Disc Pad Thickness

Courtesy of MAZDA MOTORS CORP.

FRONT BRAKE (DISC) REMOVAL/INSTALLATION

1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. After installation, add brake fluid, bleed the air, and inspect for fluid leakage. (See

AIR BLEEDING

.)

4. After installation, depress the brake pedal a few times, rotate the wheel by hand, and verify that the brake

does not drag.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Conventional Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:49 AM

Page 20

© 2005 Mitchell Repair Information Company, LLC.

«
...
533
534
535
536
537
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Parrot Страницы: 19

Бренд: Parrot Страницы: 88

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 2

CK 3000 Evolution

Бренд: Parrot Страницы: 8

CK 3000 Evolution

Бренд: Parrot Страницы: 106

ESCALADE FAMILY - SPECIFICATIONS 2011

Бренд: Cadillac Страницы: 1

Бренд: Allen Sports Страницы: 2

Бренд: Whelen Engineering Company Страницы: 9

PRIME DESIGN URX-001-E

Бренд: Safe Fleet Страницы: 8

Ford 4” UNI-CAM

Бренд: Nav TV Страницы: 6

2007 9-3 Remote Starter

Бренд: Saab Страницы: 304

Бренд: Brodit Страницы: 2

Бренд: Abrams Страницы: 12

Бренд: Thule Страницы: 8

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Бренд: ADS Страницы: 25

Бренд: Voxx Electronics Страницы: 15

Бренд: Yakima Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды