Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 601 | Manualshive

Страница: 601 / 2589

background image

Fig. 12: Identifying Rear Differential Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

LOCKNUT REMOVAL NOTE

1. Lock the hub by applying the brakes.
2. Knock the crimped portion of the locknut outward using a small chisel and a hammer.
3. Loosen the locknut.
4. Temporarily tighten the locknut.

CAUTION:

z

Do not remove the locknut when lowering the rear differential.
Otherwise, the rear drive shaft could fall and cause injury, or

damage the part.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Differential - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:52:15 AM

Page 8

© 2005 Mitchell Repair Information Company, LLC.

«
...
599
600
601
602
603
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Mazda Страницы: 4

Бренд: Calix Страницы: 5

Бренд: Audi Страницы: 9

Бренд: Belkin Страницы: 4

Бренд: RAM Страницы: 76

Бренд: Advantech Страницы: 59

Бренд: Porsche Страницы: 313

2011 A3 Sportback

Бренд: Audi Страницы: 29

TX-STAMP-4-FC04

Бренд: Over Armour Offroad Страницы: 9

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: Lund Страницы: 12

Бренд: TracRac Страницы: 6

Бренд: U.S. General Страницы: 3

Бренд: Volkswagen Zubehör Страницы: 40

Бренд: Brodit Страницы: 2

Бренд: Subaru Страницы: 9

Бренд: Skyjacker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды