Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1824

Страница: 1824 / 2589

Check code 23

CHECK CODE INSPECTION CHART (CHECK CODE 23)

Check code 25

Using the

SST

(Fuel and thermometer checker) or

resistor, input

100 ohms

between instrument cluster

terminals 1D and 1R.

Inspect the fuel
gauge sender

unit.

Except above

Go to the next

step.

Inspect the wiring harness and connector between instrument cluster and fuel gauge sender unit.

If there is any malfunction, repair or replace the wiring harness or connector.

If there is no malfunction, replace the instrument cluster.

Check code 23

Fuel gauge operation signal

INSPECTION

CONDITION

DISPLAY

ACTION

After selecting check code
23, wait for

approx. 2 s.

The fuel gauge indicates status
in the following order

approx.

every 2 s.

F --> 1/2 --> E --> F

(fixed)

The fuel gauge

is normal.

Except above

Replace the
instrument

cluster.

Replace the instrument cluster.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 14

«
...
1822
1823
1824
1825
1826
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды