Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1933

Страница: 1933 / 2589

Fig. 23: Identifying Inboard Light, Connector, Bracket, Nut & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

INBOARD LIGHT INSTALLATION NOTE

1. Insert the inboard light into the liftgate as shown in the figure, pivot it inward and then fix in place.

Fig. 24: Inserting Inboard Light Into Liftgate

Courtesy of MAZDA MOTORS CORP.

2. Push the bracket onto the liftgate as shown in the figure and install.

Fig. 25: Pushing Bracket Onto Liftgate

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 17

«
...
1931
1932
1933
1934
1935
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды