Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 876

Страница: 876 / 2589

DIAGNOSTIC MONITORING TEST RESULTS ACCESS PROCEDURE

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "Powertrain".
2. Select "OBD Test Modes".
3. Select "Mode 6 On-Board Test Results".

When using the PDS (Pocket PC)

1. Select "OBDII Modes".
2. Select "Mode 6 On-Board Test Results".

Fig. 10: Identifying DLC-2

Courtesy of MAZDA MOTORS CORP.

3. Verify the PID data according to the directions on the screen.

SIMULATION FUNCTION PROCEDURE

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "DataLogger".
2. Select "Modules".
3. Select "PCM".

When using the PDS (Pocket PC)

VT DIFF1

(RH)

VT DIFF2

Difference between target and actual valve timing

(LH)

VT DUTY1

Oil control valve duty value (RH)

VT DUTY2

Oil control valve duty value (LH)

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:08:34 AM

Page 12

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды