Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1943

Страница: 1943 / 2589

REMOVAL/INSTALLATION

3. Remove the hood release lever. (See

HOOD LATCH AND RELEASE LEVER

REMOVAL/INSTALLATION

4. Remove in the order indicated in the table.

Fig. 46: Identifying Headlight Leveling Switch & Connector

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

HEADLIGHT LEVELING SWITCH INSPECTION

1. Verify that continuity between the headlight leveling switch terminals is as indicated in the table.

If not as indicated in the table, replace the headlight leveling switch.

Fig. 47: Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 27

«
...
1941
1942
1943
1944
1945
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды