Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2392

Страница: 2392 / 2589

FRONT SIDE

1. Measure the voltage at each terminal (other than terminals 1M and 2A).

If the voltage is not as specified in the Terminal Voltage Table, inspect the parts under "inspection
item(s)" and related wiring harnesses.

2. Disconnect the negative battery cable.
3. If the system does not work properly even though the inspection items or related wiring harnesses do not

have any malfunction, replace the power window main switch.

Fig. 19: Identifying Power Window Main Switch Connector Terminal

Courtesy of MAZDA MOTORS CORP.

VOLTAGE SPECIFICATION

ensure the POWER WINDOW INITIALIZATION PROCEDURE has been

performed.

Terminal Signal name

Connected

Measured

condition

Voltage (V)/

Continuity

Inspection item (s)

IG 1

METER 10

A fuse

Ignition switch is
at ON position

B+

Inspect METER 10 A
fuse

Related wiring harnesses

Ignition switch is

at LOCK

position

1.0 or less

Power-cut

signal

Power

window

subswitch

Ignition switch at
ON and power-

cut switch at
UNLOCK

B+

Power window

subswitch (See

POWER

WINDOW

SUBSWITCH
INSPECTION

)

Related wiring harnesses

Communication

Power

window

subswitch

Because this terminal is for

communication, good/no good

judgment by terminal voltage is

not possible.

Power window

subswitch (See

POWER

WINDOW

SUBSWITCH
INSPECTION

)

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 13

«
...
2390
2391
2392
2393
2394
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды