Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2395

Страница: 2395 / 2589

PASSENGER SIDE

1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See

INNER GARNISH REMOVAL/INSTALLATION

3. Remove the front door trim. (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

)

4. Remove the screw, and remove the power window subswitch from inside the front door trim.
5. Install in the reverse order of removal.

Fig. 21: Identifying Power Window Subswitch & Screw (Passenger Side)

Courtesy of MAZDA MOTORS CORP.

REAR SIDE

1. Disconnect the negative battery cable.
2. Remove the inner sail garnish. (See

INNER SAIL GARNISH REMOVAL/INSTALLATION

3. Remove the rear door trim. (See

REAR DOOR TRIM REMOVAL/INSTALLATION

)

4. Remove the screw, and remove the power window subswitch from inside the front door trim.
5. Install in the reverse order of removal.

Fig. 22: Identifying Power Window Subswitch & Screw (Rear Side)

Courtesy of MAZDA MOTORS CORP.

POWER WINDOW SUBSWITCH INSPECTION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 16

«
...
2393
2394
2395
2396
2397
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды