Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1483

Страница: 1483 / 2589

Tube with board thickness 2 mm {0.079 in} or more

Fig. 116: Identifying Front Oil Seal With SST

Courtesy of MAZDA MOTORS CORP.

CRANKSHAFT PULLEY INSTALLATION NOTE

1. Install the crankshaft pulley, washer, and

SST

to the crankshaft.

Fig. 117: Identifying Crankshaft Pulley, Washer & SST

Courtesy of MAZDA MOTORS CORP.

2. Tighten the

SST

nut and install the crankshaft pulley.

NOTE:

Lubricate the contact surface (exterior area of inner diameter) of the front

oil seal with clean engine oil.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 73

«
...
1481
1482
1483
1484
1485
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды