Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2452

Страница: 2452 / 2589

Fig. 24: Wiper And Washer Switch Terminals Continuity Chart (Vehicles With Auto Wiper
System)

Courtesy of MAZDA MOTORS CORP.

REAR WIPER AND WASHER SWITCH INSPECTION

1. Verify that the continuity between the rear wiper and washer switch terminals is as indicated in the table.

If not as indicated in the table, replace the wiper and washer switch.

Fig. 25: Rear Wiper And Washer Switch Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 17

«
...
2450
2451
2452
2453
2454
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды