background image

3651 N. Highway 89 • Chino Valley, AZ 86323

(928) 636-3100 • www.orfab.com

JEEP WRANGLER JK

ROCK SLIDER REAR BUMPER

WITH LED BACK-UP LAMPS

INSTALLATION INSTRUCTIONS

2007-2016

KIT# 83218

 WARNING

Before  you  install  this  kit,  read  and  understand  all 

instructions,  warnings,  cautions,  and  notes  in  this 

instruction sheet and in the vehicle owner’s manual.

 CAUTION

Proper installation of this kit requires knowledge of the 

factory  recommended  procedures  for  removal  and 

installation of original equipment components. We rec-

ommend that the factory shop manual and any special 

tools needed to service your vehicle be on hand during 

the  installation.  Installation  of  this  kit  without  proper 

knowledge  of  the  factory  recommended  procedures 

may affect the performance of these components and 

the safety of the vehicle. We strongly recommend that 

a certified mechanic familiar with the installation of sim-

ilar components install this kit.

 WARNING

Many  states  and  municipalities  have  laws  restricting 

bumper  heights  and  “types”.  Consult  state  and  local 

laws to determine if the changes you intend to make to 

the vehicle comply with the law. 

 WARNING

Always  wear  eye  protection  when  operating  power 

tools.

 WARNING

Before you install this kit, block the vehicle tires to pre-

vent the vehicle from rolling.

NOTE

OR-FAB Inc. recommends using the Loctite® supplied 

in the kit on the threads of all kit nuts and bolts unless 

specified otherwise in these instructions.

Before Starting Installation

1.

Carefully  read  all  warnings  and  instructions  com-

pletely before beginning.

2.

Verify  all  parts  have  been  received  in  this  kit  by 

checking the parts list at the end of this document.

3. Only install this kit on the vehicle for which it is 

specified.

  If  anytime  during  the  installation  you 

encounter something different from what is outlined 

in  the  instructions,  call  technical  support  at: 

(928) 636-3100.

4.

Park vehicle on a clean, dry, flat, level surface and 

block tires so vehicle cannot roll in either direction.

Engine Compartment

Disconnect both battery cables. Disconnect nega-

tive cable first, then positive cable.

NOTE

Kit  parts  are  prefaced  by  the  word 

kit

  and  appear  in 

bold

 print.

NOTE

If parts are missing from kit, please be prepared to pro-

vide the following information:

1. 

Name

 of purchase location

2. 

Bar Code

 on side of box

3. 

Date

 above bar code

4. 

Date

 inside box cover

5. 

Inspector #

 from inside box cover

Positive Cable

Negative Cable

WRANGLER JK/JKU

1

Rock Slider Rear Bumper w/LED Lamps - Kit 83218

421 MAIN STREET, RIVERSIDE CA, 92501   |   UNITED STATES   |   (951)-680-9595   |   

WWW.ORFAB.COM

INSTALLATION INSTRUCTIONS

 

JEEP Wrangler JK Rock Slider HD 
Rear Bumper | 

2007-2017

Item

Kit No.

HD Bumper

83208/83268

WARNINGS/CAUTIONS

Before you install this kit, read and understand 
all instructions, warnings, cautions, and notes in 
this instruction sheet and in the vehicle owner’s 
manual.

Proper installation of this kit requires knowledge 
of the factory recommended procedures for removal 
and installation of original equipment components. 
We recommend that the factory shop manual and 
any special tools needed to service your vehicle 
be on hand during the installation. Installation of 
this kit without proper knowledge of the factory 
recommended procedures may affect the perfor-
mance of these components and the safety of the 
vehicle. We strongly recommend that a certified 
mechanic familiar with the installation of similar 
components install this kit.

Many states and municipalities have laws 
restricting bumper heights and "type". Consult 
state and local laws to determine if the changes 
you intend to make to the vehicle comply with 
the law.

Always wear eye protection when operating  
power tools.

Before you install this kit, block the vehicle tires 
to prevent the vehicle from rolling.

OR-FAB Inc. recommends using the Loctite

®

 supplied 

in the kit on the threads of all kit nuts and bolts 
unless specified otherwise in these instructions.

If parts are missing from kit, please be prepared 
to provide the following information:
  1.  Name of purchase location
  2.  Bar Code on side of box
  3.  Date above bar code
  4.  Date inside box cover
  5.  Inspector # from inside box cover

NOTE

Kit parts are prefaced by the word kit 

and appear in bold print.

BEFORE STARTING INSTALLATION

1.   Carefully read all warnings and instructions 

completely before beginning.

2.   Verify all parts have been received in this kit 

by checking the parts list at the end of this 
document.

3.  

Only install this kit on the vehicle for 
which it is specified.
 If anytime during  
the installation you encounter something  
different from what is outlined in the  
instructions, call technical support at the 
number below.

4.   Park the vehicle on a clean, dry, flat, level 

surface and block the tires so the vehicle 
cannot roll in either direction.

ENGINE COMPARTMENT

Отзывы: