Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1419

Страница: 1419 / 2589

pulley.

3. Turn the crankshaft clockwise to install the power steering oil pump drive belt.

Fig. 8: Positioning Power Steering Oil Pump Drive Belt

Courtesy of MAZDA MOTORS CORP.

4. Install the generator and A/C drive belt. (See

GENERATOR AND A/C DRIVE BELT

5. Verify that the drive belt auto tensioner indicator mark does not exceeds the maximum belt length. (See

DRIVE BELT INSPECTION [MZI-3.7]

If it exceeds the maximum belt length, replace the generator and A/C drive belt.

Fig. 9: Identifying Power Steering Oil Pump Drive Belt With Pulleys

Courtesy of MAZDA MOTORS CORP.

DRIVE BELT AUTO TENSIONER INSPECTION [MZI-3.7]

1. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7]

NOTE:

Hold the SST and power steering oil pump drive belt by hand

until the power steering oil pump drive belt is properly seated.

NOTE:

Verify that the power steering oil pump drive belt is firmly attached to

the pulleys.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 9

«
...
1417
1418
1419
1420
1421
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды