Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1713

Страница: 1713 / 2589

Fig. 55: Refrigerant Pressure Switch Terminals Continuity Chart (3 Of 3)

Courtesy of MAZDA MOTORS CORP.

FRONT CLIMATE CONTROL UNIT REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Decoration panel (See

DECORATION PANEL REMOVAL/INSTALLATION

2. Front console box mat (See

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

3. Indicator panel (See

INDICATOR PANEL REMOVAL/INSTALLATION

4. Front console box (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

5. Center panel (See

CENTER PANEL REMOVAL/INSTALLATION

3. Remove the screws.
4. Remove the front climate control unit.
5. Install in the reverse order of removal.

Fig. 56: Identifying Front Climate Control Unit & Screws

Courtesy of MAZDA MOTORS CORP.

FRONT CLIMATE CONTROL UNIT INSPECTION

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 34

«
...
1711
1712
1713
1714
1715
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды