Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1794

Страница: 1794 / 2589

Fig. 21: Identifying Rear Heater Hose No.1 & No.2

10. Remove in the order indicated in the table
11. Install in the reverse order of removal.
12. Perform the refrigerant system performance test.

(See

REFRIGERANT SYSTEM PERFORMANCE TEST

Fig. 22: Identifying Rear A/C Unit Removal Order & Torque Specifications

REAR A/C UNIT DISASSEMBLY/ASSEMBLY

1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.

2008 Mazda CX-9 Grand Touring

2008 HVAC Basic System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:11:59 AM

Page 17

«
...
1792
1793
1794
1795
1796
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды