Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 704 | Manualshive

Страница: 704 / 2589

background image

Fig. 11: Identifying Master Cylinder (Primary Side & Secondary Side)

Courtesy of MAZDA MOTORS CORP.

DSC/RSC HU/CM CONNECTOR INSTALLATION NOTE

1. Install the DSC/RSC HU/CM connector using the following procedure:

1. After verifying that the lock lever is locked by the lower tab, connect the DSC/RSC HU/CM

connector to the DSC/RSC HU/CM.

2. Pull up the lock lever by pressing the lower tab, and release the lock.
3. Pull up the lock lever and lock it using the upper tab.

2. Verify that the DSC/RSC HU/CM connector is installed securely.

Fig. 12: View Of DSC/RSC HU/CM Connector

Courtesy of MAZDA MOTORS CORP.

DSC/RSC HU AIR BLEEDING

1. Turn the ignition switch off.
2. Connect the M-MDS to the DLC-2.
3. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

z

When using the IDS (laptop PC)

1. Select "Chassis".
2. Select "Braking".

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.

«
...
702
703
704
705
706
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: GMC Страницы: 140

Бренд: Oldsmobile Страницы: 360

Бренд: Yakima Страницы: 19

UCI-11C NTV-KIT331

Бренд: Nav TV Страницы: 4

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

Бренд: Fiat Страницы: 172

Бренд: Honda Страницы: 6

Бренд: Boyo Страницы: 9

Бренд: Kargo Master Страницы: 19

PRIME DESIGN VBR3-FT31B

Бренд: Safe Fleet Страницы: 12

Бренд: Hyundai Страницы: 18

Бренд: Great Wall Страницы: 18

Бренд: WIX Страницы: 2

Бренд: UAZ Страницы: 112

RVS systems RVS-M641

Бренд: Safe Fleet Страницы: 24

GMC Yukon Denali 2005

Бренд: Cadillac Страницы: 456

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды