Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1941

Страница: 1941 / 2589

1. Verify that continuity between the front fog light switch terminals is as indicated in the table.

Fig. 41: Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 42: Checking Continuity Between Front Fog Light Switch Terminals

Courtesy of MAZDA MOTORS CORP.

HAZARD WARNING SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Decoration panel (See

DECORATION PANEL REMOVAL/INSTALLATION

2. Front console box mat (See

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

3. Indicator panel (See

INDICATOR PANEL REMOVAL/INSTALLATION

4. Front console box (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

5. Center panel (See

CENTER PANEL REMOVAL/INSTALLATION

3. Remove in hazard warning switch.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 25

«
...
1939
1940
1941
1942
1943
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды