Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1517 | Manualshive

Страница: 1517 / 2589

background image

ROOF SPEAKER INSPECTION

1. Verify the resistance between roof speaker terminals.

z

If the resistance is not within the specification, replace the roof speaker.

Resistance 3.6 ohms

2. Connect a 1.5 V battery to the roof speaker and verify that noise is heard from the roof speaker.

z

If no noise is heard, replace the roof speaker.

Fig. 25: Identifying Roof Speaker Terminals

Courtesy of MAZDA MOTORS CORP.

TWEETER REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the cover from the dashboard using a flathead screwdriver wrapped with protective tape.
3. Remove the solar radiation sensor. (LH) (See

SOLAR RADIATION SENSOR

REMOVAL/INSTALLATION

.)

4. Remove in the order indicated in the table.

Fig. 26: Identifying Tweeter Components

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 17

© 2005 Mitchell Repair Information Company, LLC.

«
...
1515
1516
1517
1518
1519
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Yakima Страницы: 4

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Бренд: Lincoln Страницы: 424

Бренд: Volkswagen Страницы: 26

Бренд: Roav Страницы: 10

Бренд: Neuspeed Страницы: 2

10-8002-C11998B

Бренд: Saleen Страницы: 12

2013 Buick Verano

Бренд: Buick Страницы: 5

Бренд: FormFit Страницы: 4

Бренд: Caltrend Страницы: 2

Бренд: Audiovox Страницы: 1

EGR-3PVE-COLOUR

Бренд: EGR Страницы: 28

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Бренд: HAUL MASTER Страницы: 8

Evo All THAR-FOR3

Бренд: Fortin Страницы: 7

Sedan CIVIC 2022

Бренд: Honda Страницы: 701

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды