background image

 

FORM FIT

 

HOOD PROTECTOR 

 

   

GMC ½ Ton Truck 2007 - 

 

 

 

 

 

 

       

                   

HD

 

23A 07

 

Hardware Kit

 

 

   

Tools Required 

 

3 – Adhesive Backed Pedestals           

4 – 3M Anti-Abrasion Film Pad 

   1 – Phillips Screwdriver #2 

3 – Square Expansion Plugs 

4– Clip Bodies 

1 – Tape Measure 

3 – #8 x 7/16” Black Screws 

4 – Pins 

 

1 – Masking Tape and Pencil 

3 – Large Bumpons 

4 – ‘L’ Brackets  

1 – Alcohol Wiping Pad 

4 – #6 x 5/8” Flat Head Screws 

1 – 3M Adhesive Promoter 

 

   

 

 

Installation      

1.  Be sure that the hood is clean and dry inside and out. 
2. 

Locate the center

 

of the hood

 using tape measure and the upper grill insert or body lines as references.  Place a piece of masking tape on top of the grill 

near center, where the grill meets the painted surface of the hood.  Mark the masking tape with a pencil at the center.  

See Illustration.

 

3.  Place two (2) additional pieces of masking tape on the grill to mark the location of the adhesive backed pedestals.  Mark the masking tape with a pencil at 

the location as shown.

 

 
 

CENTER 

315mm                  315mm 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

5.  Temporarily tape the pedestals to surface of the hood in their determined positions, confirm correct placement by placing the hood protector on top of the 

three pedestals.  When positioned correctly the three (3) holes in the center area of the protector will align with the holes in the expansion plugs.  Adjust 
if necessary and reconfirm the pedestal locations using the measurements in the illustration and the hood protector. 

 

4.  Install the square expansion plugs into the top of the adhesive backed pedestals.  Use the centering notch on the pedestals to align it’s location with 

the pencil mark on the tape in the previous Step. 

Note:

  When located correctly the pedestal leading edge will butt against the back of the grill 

surround at all 3 locations. 

 

 

 

 

 

 

 

 

 

 

 

6.

  

Remove the pedestals and clean the contact with alcohol wiping pad.

 

Tip:

 Before removing the pedestals, use masking tape to outline the area of the hood where the pedestals will mount.  After installation the tape can be 

removed and there will be no clean up of the mounting area required and final placement of the pedestals will be easier.  

See Illustration. 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

Содержание HD 23A 07

Страница 1: ... 315mm 315mm 5 Temporarily tape the pedestals to surface of the hood in their determined positions confirm correct placement by placing the hood protector on top of the three pedestals When positioned correctly the three 3 holes in the center area of the protector will align with the holes in the expansion plugs Adjust if necessary and reconfirm the pedestal locations using the measurements in the...

Страница 2: ...tick them to the hood centered underneath the holes in the protector See Illustration Step 10 11 a Place a clip over each of the anti abrasion film pads on the edge of the hood as shown in Illustration Step 11a b Insert a pin through the protector into each of the clips See Illustration Step 11b c Insert a 6 x 5 8 screw through an L bracket and into the clip See Illustration Step 11c 11d d Make su...

Страница 3: ...rairement les piédestaux de bandes à la surface du capot déterminée dans leurs positions confirmer placement correct en plaçant le capuchon protecteur au dessus des trois piédestaux Lorsque positionné correctement les 3 trous dans la zone centrale de la volonté aligne protecteur avec les trous dans bouchon l expansion Ajustez si nécessaire et réaffirmer le piédestaux emplacements en utilisant les ...

Страница 4: ... 115mm 100mm 11a Monter une agrafe sur chaque tampon anti abrasif sur la bordure du capot Voir l illustration étape n 11a b Insérer une épingle au travers du protecteur et dans I agrafe Voir l illustration étape n 11b c Insérer une vis n 6 x 5 8 po au travers du braquet en forme L et dans l agrafe Voir l illustration étape n 11c et n 11d d S assurer que tous les composants sont bien installés sur ...

Отзывы: