Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 629

Страница: 629 / 2589

Fig. 1: Identifying Door & Liftgate Components Location

Courtesy of MAZDA MOTORS CORP.

FRONT DOOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. To remove the checker, remove the following parts:

1. Inner garnish (See

INNER GARNISH REMOVAL/INSTALLATION

2. Front door trim (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

3. Front door speaker (See

FRONT DOOR SPEAKER REMOVAL/INSTALLATION

3. To remove the front door hinges, remove the following parts:

1. Windshield wiper arm and blade (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

2. Side cowl grille (See

COWL GRILLE REMOVAL/INSTALLATION

3. Front bumper (See

FRONT BUMPER REMOVAL/INSTALLATION

4. Front combination lights (See

FRONT COMBINATION LIGHT

REMOVAL/INSTALLATION

5. Sail garnish (See

SAIL GARNISH REMOVAL/INSTALLATION

6. Front fender panel (See

FRONT FENDER PANEL REMOVAL/INSTALLATION

4. Remove in the order indicated in the table.

Fig. 2: Identifying Front Door Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Doors and Liftgate - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:45:22 AM

Page 3

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды