Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 846

Страница: 846 / 2589

CMP sensor (LH) terminal B and power supply

FRONT HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION

[MZI-3.7]

HO2S (LH) REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7]

3. Disconnect the HO2S (LH) connector.

4. Remove the HO2S (LH) using the SST.

5. Install in the reverse order of removal.

Fig. 25: View Of HO2S (LH), SST & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

HO2S (RH) REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following part for easier access.

1. Remove the cowl panel. (See

COWL PANEL REMOVAL/INSTALLATION

3. Disconnect the HO2S (RH) connector.

NOTE:

If necessary, lubricate the HO2S with Penetrating and Lock Lubricant

loosen to aid in removal.

NOTE:

Apply a light coat of anti-seize lubricant to the threads of the HO2S.

NOTE:

If necessary, lubricate the HO2S with Penetrating and Lock Lubricant

loosen to aid in removal.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 28

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды