Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 397

Страница: 397 / 2589

1. Insert a precision screwdriver from the backside into the connector as shown in the figure.

Fig. 89: Identifying Backside Into Connector

Courtesy of MAZDA MOTORS CORP.

2. Pry the screwdriver in the direction of the arrow and disconnect the connector.

Fig. 88: Tapping Control Valve Body Cover
Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not damage the solenoid valves and connectors with

the screwdriver.

When disconnecting connectors, grasp the connectors,

not the harnesses. Otherwise, the harnesses may be
pulled out of the connector causing poor contact.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 69

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды