Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1836

Страница: 1836 / 2589

Check code 04

CHECK CODE INSPECTION CHART (CHECK CODE 04)

Select the check
code 02. (The

diagnostic results
will be displayed

once each in the
order of audio unit

and heater control
unit.)

Audio unit

Communication to audio

unit is normal.

Communication error to

audio unit. (DTC U0184)

(See

DTC TABLE

[MULTIPLEX

COMMUNICATION

SYSTEM]

)

Vehicle without audio unit.

Climate control

unit

Communication to climate

control unit is normal.

Communication error to

climate control unit. (DTC

U0164)

(See

DTC TABLE

[MULTIPLEX

COMMUNICATION

SYSTEM]

)

Vehicle without climate

control unit.

Check code 04

TNS relay ON/OFF signal

STEP

INSPECTION

CONDITION

DISPLAY

ACTION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 26

«
...
1834
1835
1836
1837
1838
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды