Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1922

Страница: 1922 / 2589

Fig. 6: Turning Aiming Adjustment Screw

Courtesy of MAZDA MOTORS CORP.

HEADLIGHT BULB REMOVAL/INSTALLATION

LOW-BEAM

Halogen type

1. Disconnect the negative battery cable.
2. Remove the coolant reserve tank. (RH only) (See

COOLANT RESERVE TANK

REMOVAL/INSTALLATION [MZI-3.7]

3. Remove in the order indicated in the table.

Fig. 7: Identifying Halogen Headlight Bulb, Connector & Cover

Courtesy of MAZDA MOTORS CORP.

CAUTION:

A halogen bulb generates extremely high heat when it is

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:05 AM

Page 6

«
...
1920
1921
1922
1923
1924
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды