Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 442

Страница: 442 / 2589

1. Disconnect the negative battery cable.
2. To remove the hood hinges, remove the following parts:

1. Windshield wiper arm and blade (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

)

2. Side cowl grille (See

COWL GRILLE REMOVAL/INSTALLATION

)

3. Remove in the order indicated in the table.

Fig. 3: Identifying Hood Removing Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.
5. Adjust the hood. (See

HOOD ADJUSTMENT

GAP ADJUSTMENT

1. Measure the gap between the hood and body.

fall and cause serious injury. Always perform the procedure with at

least another person to prevent the hood from falling.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:45 AM

Page 3

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды