Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2080

Страница: 2080 / 2589

1. Drain the engine oil. (See

ENGINE OIL REPLACEMENT [MZI-3.7]

2. Remove the engine and transaxle component. (See

ENGINE REMOVAL/INSTALLATION [MZI-

3.7]

3. Secure the engine and transaxle component using a hoist and the

SST.

4. Remove the dynamic chamber and throttle body as a single unit. (See

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.7]

5. Remove the ignition coils. (See

IGNITION COIL REMOVAL/INSTALLATION [MZI-3.7]

6. Remove the dipstick.
7. Remove the power steering oil pump drive belt. (See

DRIVE BELT REMOVAL/INSTALLATION

[MZI-3.7]

8. Remove the power steering oil pump. (See

POWER STEERING OIL PUMP

REMOVAL/INSTALLATION

9. Remove the timing chain component. (See

TIMING CHAIN REMOVAL/INSTALLATION [MZI-

3.7]

Fig. 20: Lifting Engine With Engine Jack

Courtesy of MAZDA MOTORS CORP.

10. Remove in the order indicated in the table.
11. Install in the reverse order of removal.
12. Start the engine and:

NOTE:

The following procedure "OIL PUMP REMOVAL/INSTALLATION" is
performed after the engine and transaxle component is removed from the

vehicle.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Lubrication (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:14 AM

Page 16

«
...
2078
2079
2080
2081
2082
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды