Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2424 | Manualshive

Страница: 2424 / 2589

background image

Fig. 64: Identifying Mirror Glass Holder & Outer Mirror Glass

Courtesy of MAZDA MOTORS CORP.

OUTER MIRROR GLASS INSTALLATION

1. Connect the heated outer mirror connectors, (vehicles with heated outer mirrors)
2. Connect the BSM indicator light connector, (vehicles with BSM)
3. Press part A on the outer mirror glass and install pin A.
4. Press part B on the outer mirror glass and install pins B.

Fig. 65: Identifying BSM Indicator Light Connector, Outer Mirror Glass & Mirror Glass Holder

Courtesy of MAZDA MOTORS CORP.

OUTER MIRROR GARNISH REMOVAL

1. Remove the outer mirror glass from the outer mirror. (See

OUTER MIRROR GLASS REMOVAL

.)

2. Pinch the ends of the visible clips (4 locations) shown in the figure, and detach them by pressing them

towards the vehicle front.

3. Grasp the upper side of the outer mirror garnish and remove it by pulling it in the direction of the arrow.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:17 AM

Page 45

© 2005 Mitchell Repair Information Company, LLC.

«
...
2422
2423
2424
2425
2426
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

Бренд: Happy Orange Страницы: 2

Бренд: Back View Страницы: 168

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 7

Cherokee 16 1982

Бренд: Jeep Страницы: 1311

Бренд: Carcomm Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Carpower CAP-20

Бренд: Monacor Страницы: 2

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Volvo Страницы: 284

Бренд: SCC Страницы: 4

2005 JR41 Stratus

Бренд: Dodge Страницы: 293

Бренд: RHOX Страницы: 8

Бренд: APS Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды