Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 440 | Manualshive

Страница: 440 / 2589

background image

2008 ACCESSORIES & BODY, CAB

Body Panels - Mazda CX-9

REAR BUMPER REINFORCEMENT REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the rear combination light. (See

REAR COMBINATION LIGHT

REMOVAL/INSTALLATION

.)

3. Remove the rear bumper. (See

REAR BUMPER REMOVAL/INSTALLATION

.)

4. Remove the fasteners, then remove the energy-absorbing foam.
5. Remove the bolts and nuts, then remove the rear bumper reinforcement.
6. Install in the reverse order of removal.

Fig. 1: Identifying Rear Bumper Reinforcement & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

BODY PANELS LOCATION INDEX

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:45 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Sunday, November 15, 2009 10:44:49 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
438
439
440
441
442
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Daihatsu Страницы: 1718

Бренд: Feniex Страницы: 6

Бренд: FORM FIT Страницы: 2

Бренд: Magneti Marelli Страницы: 2

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Бренд: Havis-Shields Страницы: 1

Бренд: Discount Car Stereo Страницы: 8

Бренд: Mitsubishi Страницы: 362

Бренд: Axxess Страницы: 16

Бренд: Honda Страницы: 330

Filtercharger 57-9004

Бренд: K&N Engineering Страницы: 4

Бренд: Honda Страницы: 219

Бренд: Kargo Master Страницы: 18

ASENTO EV-COLC15R

Бренд: ADAPT SOLUTIONS Страницы: 22

Бренд: ZENEC Страницы: 2

Бренд: Lexus Страницы: 609

Бренд: Proxel Страницы: 16

Бренд: Yakima Страницы: 8

Бренд: ACV Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды