Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 525 | Manualshive

Страница: 525 / 2589

background image

2. Remove the resonance chamber. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

.)

3. Remove the bolt and nut as shown in the figure, and move the vacuum pipe bracket.
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. After installation, add brake fluid, bleed the air, and inspect for fluid leakage. (See

AIR BLEEDING

.)

Fig. 12: Identifying Vacuum Pipe Bracket, Bolt, Nut & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Conventional Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:49 AM

Page 10

© 2005 Mitchell Repair Information Company, LLC.

«
...
523
524
525
526
527
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: EAL Страницы: 4

Бренд: Triumph Страницы: 86

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

2016 Sandero Stepway

Бренд: Renault Страницы: 183

Бренд: Condor Страницы: 2

Бренд: Jeep Страницы: 16

Бренд: Audi Страницы: 4

MultiCharger 1204

Бренд: DEFA Страницы: 28

Бренд: Steelmate Страницы: 14

CF-UFORCE-DRW01

Бренд: FALCON RIDGE Страницы: 6

Бренд: IOGear Страницы: 38

Бренд: Toyota Страницы: 285

Бренд: Kuda Страницы: 3

Бренд: Metra Electronics Страницы: 8

Бренд: Kargo Master Страницы: 18

Бренд: Quadratec Страницы: 2

Бренд: Buick Страницы: 20

10.297.300K-303K

Бренд: AUTOTECH Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды