Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1730

Страница: 1730 / 2589

voltage
(1W, 1X)

Panel light

control input

Instrument

cluster

Turn the headlight switch to
the off position

1.0 or less

Wiring

harness:
continuity,

short
circuit

(Rear
climate

control
unit-

instrument
cluster: G-

1I)

TNS relay

Headlight
switch

Turn the headlight switch to

the TNS position

B+

TNS signal

Front climate
control unit

Turn the headlight switch to
the off position

1.0 or less

Wiring

harness:
continuity,

short
circuit

(Front
climate

control
unit-rear

climate
control

unit: 3F-
H)

TNS relay

Headlight

switch

Turn the headlight switch to

the TNS position

B+

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 51

«
...
1728
1729
1730
1731
1732
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды