Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1708

Страница: 1708 / 2589

Fig. 47: Identifying Cabin Temperature Sensor & Cover

Courtesy of MAZDA MOTORS CORP.

CABIN TEMPERATURE SENSOR INSPECTION

1. Measure the temperature around the cabin temperature sensor and measure the resistance between cabin

temperature sensor terminal.

If the characteristics of the cabin temperature sensor are not as shown in the graph, replace the
cabin temperature sensor.

Fig. 48: Cabin Temperature Sensor Temperature & Resistance Graph

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:36 AM

Page 29

«
...
1706
1707
1708
1709
1710
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды