Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 844 | Manualshive

Страница: 844 / 2589

background image

Courtesy of MAZDA MOTORS CORP.

CAMSHAFT POSITION (CMP) SENSOR INSPECTION [MZI-3.7]

VISUAL INSPECTION

1. Remove the CMP sensor. (See

CAMSHAFT POSITION (CMP) SENSOR

REMOVAL/INSTALLATION [MZI-3.7]

.)

2. Verify that there are no metal shavings on the CMP sensor.
3. Install the CMP sensor. (See

CAMSHAFT POSITION (CMP) SENSOR

REMOVAL/INSTALLATION [MZI-3.7]

.)

RESISTANCE INSPECTION

1. Remove the CMP sensor connector.
2. Measure the resistance between the CMP sensor terminals.

z

If not within the specification, replace the CMP sensor. (See

CAMSHAFT POSITION (CMP)

SENSOR REMOVAL/INSTALLATION [MZI-3.7]

.)

z

If the monitor item status/specification (reference) is not within the specification, even though the
resistance is within the specification, perform the "Circuit Open/Short Inspection".

CMP sensor resistance

800-1,320 ohms

CIRCUIT OPEN/SHORT INSPECTION

NOTE:

z

Before performing the following inspection, make sure to follow the

procedure as indicated in the troubleshooting flowchart. (See HOW TO

USE THIS MANUAL .)

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 26

© 2005 Mitchell Repair Information Company, LLC.

«
...
842
843
844
845
846
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Mazda Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 8

Бренд: PAC Страницы: 5

V2 SUPERCHARGER

Бренд: Tesla Страницы: 9

Бренд: PEUGEOT Страницы: 128

Бренд: Schumacher Electric Страницы: 87

2009 ESCALADE ESV

Бренд: Cadillac Страницы: 602

Evo All THAR-FOR3

Бренд: Fortin Страницы: 7

Grand Cherokee SRT 2019

Бренд: Jeep Страницы: 656

Бренд: Ford Страницы: 4378

Бренд: Toyota Страницы: 549

Бренд: Sintrones Страницы: 55

Бренд: Setma Страницы: 13

Бренд: Volkswagen Zubehör Страницы: 133

Бренд: FIRRAK Страницы: 12

Бренд: EUFAB Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды