Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 990

Страница: 990 / 2589

DIAGNOSTIC PROCEDURE

DTC P0204 (MZI-3.7) DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA HAS BEEN

RECORDED

Has FREEZE FRAME DATA been recorded?

Yes Go to the next step.

Record FREEZE FRAME DATA

on the repair order, then go to the

next step.

VERIFY RELATED REPAIR INFORMATION

AVAILABILITY

Verify related Service Bulletins availability.

Is any related Service Bulletins available?

Yes

Perform repair or diagnosis

according to available Service
Bulletins.

If vehicle is not repaired, go

to the next step.

Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:08:36 AM

Page 126

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды