Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1995 | Manualshive

Страница: 1995 / 2589

background image

Fig. 46: Identifying Liftgate Lock Actuator Terminals

Courtesy of MAZDA MOTORS CORP.

LIFTGATE OUTER HANDLE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the liftgate upper trim. (See

LIFTGATE UPPER TRIM REMOVAL/INSTALLATION

.)

3. Remove the liftgate side trim. (See

LIFTGATE SIDE TRIM REMOVAL/INSTALLATION

.)

4. Remove the liftgate lower trim. (See

LIFTGATE LOWER TRIM REMOVAL/INSTALLATION

.)

5. Remove the rear finisher. (See

REAR FINISHER REMOVAL/INSTALLATION

.)

6. Disconnect the liftgate outer handle switch connector. (Vehicles with power liftgate system)
7. Disconnect the cable. (Vehicles without power liftgate system)
8. Remove in the order indicated in the table.

Fig. 47: Identifying Liftgate Outer Handle With Nut & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

9. Install in the reverse order of removal.

LIFTGATE OUTER HANDLE SWITCH INSPECTION

1. Verify that the continuity between the liftgate outer handle switch terminals is as indicated in the table.

Lock

B+ GND

Unlock GND B+

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 25

© 2005 Mitchell Repair Information Company, LLC.

«
...
1993
1994
1995
1996
1997
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Yakima Страницы: 12

Бренд: JEHNERT SOUND DESIGN Страницы: 8

Experience Series

Бренд: Rainbow Страницы: 19

Бренд: Yakima Страницы: 12

Бренд: SAN HIMA Страницы: 10

Бренд: Fab Fours Страницы: 21

Бренд: TAUBENREUTHER Страницы: 18

PRIME DESIGN HRR3-E-PM42

Бренд: Safe Fleet Страницы: 12

Бренд: N.R. AUTOSEATS Страницы: 8

Бренд: Poison Spyder Страницы: 5

Бренд: Mercedes-Benz Страницы: 27

Бренд: Honda Страницы: 5

Бренд: Metra Electronics Страницы: 12

MagicComfort MSH50

Бренд: Waeco Страницы: 104

Бренд: Curt Group Страницы: 4

Бренд: Nedap Страницы: 18

Бренд: VanEssa mobilcamping Страницы: 12

Бренд: Suzuki Страницы: 190

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды