Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 483

Страница: 483 / 2589

DTC C1222 [DSC/RSC]

DTC C1222 [DSC/RSC] DETECTION CONDITION AND POSSIBLE CAUSE

DIAGNOSTIC PROCEDURE

DTC C1222 [DSC/RSC] DIAGNOSTIC PROCEDURE

Clear the DTC from the memory.

(See

ON-BOARD DIAGNOSTIC

[DSC/RSC]

Are the same DTCs present?

Yes

If the malfunction recurs, replace the
DSC/RSC HU/CM, then go to the next step.

(See

DSC/RSC HU/CM

REMOVAL/INSTALLATION

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

Are any other DTCs present?

Yes

Go to the applicable DTC inspection.
(See

ON-BOARD DIAGNOSTIC

[DSC/RSC]

DTC troubleshooting completed.

DTC C1222

ABS wheel-speed sensor system

DETECTION

CONDITION

When the difference in the wheel speed between one tire and the others
exceeds 25%.

POSSIBLE CAUSE

A tire of different diameter is installed.

An incorrect ABS sensor rotor is installed (different number of teeth).

STEP

INSPECTION

ACTION

INSPECT PID (WHEEL SPEED) FOR

DIFFERENCE IN EACH WHEEL
SPEED USING M-MDS

Turn the ignition switch off.

Connect the M-MDS to the DLC-2.

Select the following PIDs using the
M-MDS:

WSPD_LF

WSPD_LR

WSPD_RF

WSPD_RR

Drive the vehicle.

Verify that the wheel speeds detected

Yes Go to Step 4.

Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 BRAKES On-Board Diagnostic (DSC/RSC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:13 AM

Page 27

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды