Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1908

Страница: 1908 / 2589

Fig. 70: Identifying Trunk Box With Clips

Courtesy of MAZDA MOTORS CORP.

SEAT SIDE BOX REMOVAL/INSTALLATION

WITH BOSE®

1. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

2. Detach clips A and tab B by pulling them in the direction of the arrow.
3. Remove the seat side box.
4. Install in the reverse order of removal.

Fig. 71: Identifying Seat Side Box With Clips & Tab

Courtesy of MAZDA MOTORS CORP.

WITHOUT BOSE®

1. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

2. Detach pins by pulling them in the direction of the arrow.
3. Remove the seat side box.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 44

«
...
1906
1907
1908
1909
1910
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды