Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2351 | Manualshive

Страница: 2351 / 2589

background image

2008 DRIVELINE/AXLE

Transfer - Mazda CX-9

TRANSFER LOCATION INDEX

Fig. 1: Identifying Transfer Oil Seal And Transfer

Courtesy of MAZDA MOTORS CORP.

TRANSFER SERVICE CAUTIONS

z

Do not perform overhauling and other servicing such as transfer oil inspection, adjustment, and

replacement. Adjusting the oil amount leads to over-fill or under-fill, which could cause oil leakage or
seizure of the transfer while driving. In addition, internal parts for overhauling are not available.

z

A maintenance-free type transfer has been adopted. If there is a malfunction with the transfer unit, replace

the transfer as a single component.

TRANSFER OIL SEAL REPLACEMENT

RIGHT SIDE

1. Remove the middle pipe. (See

EXHAUST SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

.)

2. Remove the front pipe. (See

EXHAUST SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

.)

3. Remove the joint shaft. (See

JOINT SHAFT REMOVAL/INSTALLATION [AWD]

.)

4. Using the

SST

, remove the deflector.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Transfer - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Transfer - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:32:26 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Sunday, November 15, 2009 10:32:29 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
2349
2350
2351
2352
2353
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Metra Electronics Страницы: 2

Chevrolet Silverado 2500HD 2021

Бренд: GMC Страницы: 433

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Бренд: Honda Страницы: 4

SAFESTOP SS0005

Бренд: Pro-gard Страницы: 4

Challenger 2013

Бренд: Dodge Страницы: 543

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

SANICON TURBO 300

Бренд: Thetford Страницы: 25

PRIME DESIGN HRR-369-E-UM3-96

Бренд: Safe Fleet Страницы: 12

Бренд: Kocchi's Страницы: 4

INDICA eV2 XETA CNG

Бренд: TATA Motors Страницы: 24

Бренд: PAC Страницы: 5

Бренд: Percon Страницы: 49

Бренд: Xingyun Страницы: 74

Бренд: Kia Страницы: 233

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды