Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 493

Страница: 493 / 2589

DTC C1446 [DSC/RSC] DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

VERIFY OPEN OR SHORT CIRCUIT
IN BRAKE SWITCH SIGNAL

Turn the ignition switch to the ON

position.

Measure the voltage between the
PCM terminal 1T and body ground

when the brake pedal is depressed
and released:

Voltage

Brake pedal depressed: B+

Brake pedal released:

1 V or less

Yes Go to Step 5.

If it is B+ under any condition, then go to the next

step. If it is 1 V or less under any condition, then

go to Step 3.

INSPECT BRAKE SWITCH SIGNAL
FOR SHORT TO POWER SUPPLY

CIRCUIT

Disconnect the brake switch
connector.

Measure the voltage between the

brake switch connector terminal D
(vehicle harness-side) and body

ground.

Is the voltage

1 V or less

Yes Go to Step 4.

No Repair or replace the wiring harness between the

PCM and brake switch, then go to Step 5

INSPECT BRAKE SWITCH SIGNAL

FOR OPEN CIRCUIT

Disconnect the PCM connectors.

Disconnect the brake switch
connector.

Inspect continuity between the PCM
connector terminal 1T (vehicle

harness-side) and brake switch
terminal D:

Is there continuity?

Yes Go to the next step.

Repair or replace the wiring harness between the

PCM and brake switch, then go to Step 5.

INSPECT BRAKE SWITCH

Inspect the brake switch.

Yes Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 BRAKES On-Board Diagnostic (DSC/RSC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:13 AM

Page 37

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды