Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2394

Страница: 2394 / 2589

1. Remove the power window main switch. (See

POWER WINDOW MAIN SWITCH

REMOVAL/INSTALLATION

2. When inspecting the rear, turn the power-cut switch UNLOCK.
3. Inspect for continuity between the power window main switch terminals.

If not as specified, replace the power window main switch.

Fig. 20: Power Window Main Switch (Rear Side) - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

POWER WINDOW SUBSWITCH REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 15

«
...
2392
2393
2394
2395
2396
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды