Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 191

Страница: 191 / 2589

53. Remove the counter gear component.

54. Remove the differential component.

NOTE:

Inspect the direction of the parking pin.

Fig. 53: Identifying Parking Pin
Courtesy of MAZDA MOTORS CORP.

NOTE:

For easy removal, tilt the counter gear component slightly.

Fig. 54: Identifying Counter Gear Component
Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not damage the VSS wiring harness.

Do not pull hard on the VSS wiring harness.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 28

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды