Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1542

Страница: 1542 / 2589

2008 ENGINE

Exhaust System (MZI-3.7) - Mazda CX-9

EXHAUST SYSTEM INSPECTION [MZI-3.7]

1. Start the engine and inspect each exhaust system component for exhaust gas leakage.

If leakage is found, repair or replace as necessary.

EXHAUST SYSTEM REMOVAL/INSTALLATION [MZI-3.7]

1. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

2. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7]

3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.

WARNING:

When the engine and exhaust system are hot, they can badly burn.
Turn off the engine and wait until they are cool before removing the

exhaust system.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Exhaust System (MZI-3.7) - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 ENGINE Exhaust System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:59:10 AM

Page 1

Microsoft

Sunday, November 15, 2009 9:59:14 AM

Page 1

«
...
1540
1541
1542
1543
1544
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды