Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 431

Страница: 431 / 2589

4. Front A/C unit (See

FRONT A/C UNIT REMOVAL/INSTALLATION

4. To remove the selector lever, remove the following parts.

1. Console (See

CONSOLE REMOVAL/INSTALLATION

5. Remove in the order shown in the figure.
6. Install in the reverse order of removal.

Fig. 22: Identifying Selector Lever Component Removal/Installation & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

SELECTOR CABLE REMOVAL NOTE

1. Remove the clip.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 11

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды