Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1576 | Manualshive

Страница: 1576 / 2589

background image

Fig. 3: Exploded View Of Wheel Hub, Steering Knuckle & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

LOCKNUT REMOVAL NOTE

1. Lock the hub by applying the brakes.
2. Knock the crimped portion of the locknut outward using a small chisel and a hammer.
3. Remove the locknut.
4. Install a spare nut onto the drive shaft so that the nut is flush with the end of the drive shaft.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Front Axle - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:53:51 AM

Page 3

© 2005 Mitchell Repair Information Company, LLC.

«
...
1574
1575
1576
1577
1578
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 8

Бренд: PAC Страницы: 5

Бренд: GMC Страницы: 425

Бренд: Mazdaspeed Страницы: 8

Transit Vancouver Wagon

Бренд: Webasto Страницы: 44

Бренд: Raytel LLC Страницы: 40

Бренд: Dacia Страницы: 238

Ferrari 360 Map Carbon Light

Бренд: MAcarbon Страницы: 4

Бренд: EUFAB Страницы: 16

Бренд: Mitsubishi Страницы: 19

Бренд: cam Страницы: 28

Бренд: TATA Motors Страницы: 151

QUICKDRAW RACHET TIE-DOWNS 855

Бренд: Thule Страницы: 3

Бренд: Grillo Страницы: 71

Бренд: Mitsubishi Страницы: 490

Бренд: Audi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды