Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1523

Страница: 1523 / 2589

Fig. 36: Identifying Noise Filter Terminals

Courtesy of MAZDA MOTORS CORP.

GLASS ANTENNA INSPECTION

AM/FM

1. Inspect the glass antenna for damage visually.
2. Inspect for continuity between the glass antenna terminals using an ohmmeter.

If not as specified, replace the glass antenna. (See

FILAMENT REPAIR

Fig. 37: Glass Antenna Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 23

«
...
1521
1522
1523
1524
1525
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды