Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 374 | Manualshive

Страница: 374 / 2589

background image

Fig. 50: Identifying Manual Shaft Lever

Courtesy of MAZDA MOTORS CORP.

16. Install the clip to the selector cable as shown in the figure.
17. Shift the selector lever to P position.
18. Turn the manual shaft lever to P position.

Fig. 51: Identifying Clip To Selector Cable

Courtesy of MAZDA MOTORS CORP.

19. Connect the selector cable and install the clip.
20. Connect the TCM connector.
21. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

.)

22. Connect the negative battery cable.

23. Perform the neutral position learning. (See

NEUTRAL POSITION LEARNING

.)

WARNING:

z

If you replace the ATX or TCM, be sure to initialize the learned
values and perform neutral position learning.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 46

© 2005 Mitchell Repair Information Company, LLC.

«
...
372
373
374
375
376
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

MARTEN-FREE CAR

Бренд: Gardigo Страницы: 36

Бренд: Whispbar Страницы: 15

autoSteady AS101

Бренд: Enduro Страницы: 48

Бренд: Xhorse Страницы: 48

Бренд: Yutrax Страницы: 8

Бренд: Weltmann KFZ-Teile Страницы: 12

Бренд: S3 Power Sports Страницы: 2

2004 Impreza OUTBACK SPORT

Бренд: Subaru Страницы: 34

Бренд: iDataLink Страницы: 6

Бренд: Ford Страницы: 52

Бренд: Pontiac Страницы: 20

Бренд: r.LiNK Страницы: 21

Бренд: Toyota Страницы: 672

MAGICGRIP MGQDWD-CPO

Бренд: Scosche Страницы: 12

Бренд: Brigade Страницы: 12

Бренд: Scosche Страницы: 8

Бренд: Ford Страницы: 8

Бренд: Easee Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды