Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2218 | Manualshive

Страница: 2218 / 2589

background image

Fig. 10: Locating Locknut

Courtesy of MAZDA MOTORS CORP.

REAR WHEEL HUB BOLT REPLACEMENT

1. Remove the brake calliper component and suspend it out of the way using a cable.
2. Remove the disc plate.
3. Remove the parking brake shoe.
4. Remove the wheel hub bolt using the SST as shown in the figure.
5. Place a new wheel hub bolt in the wheel hub.

Fig. 11: Removing Wheel Hub Bolt

Courtesy of MAZDA MOTORS CORP.

6. Install the wheel hub by placing a proper sized washer on the hub, and tightening the nut as shown in the

figure.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE Rear Axle - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:54:22 AM

Page 7

© 2005 Mitchell Repair Information Company, LLC.

«
...
2216
2217
2218
2219
2220
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: JANE Страницы: 6

Бренд: Mazda Страницы: 720

Бренд: Sirius Satellite Radio Страницы: 8

Бренд: Spiral Audio Страницы: 2

Бренд: AA Products Страницы: 4

PRIME DESIGN VRR-NV200

Бренд: Safe Fleet Страницы: 12

Бренд: Jeep Страницы: 16

Бренд: Audi Страницы: 4

Бренд: Bestop Страницы: 31

RVS systems RVS-M641

Бренд: Safe Fleet Страницы: 24

Akerstroms Tx700

Бренд: LXE Страницы: 146

Бренд: DriveRight Страницы: 16

Бренд: JBL Страницы: 12

Бренд: Tesla Страницы: 274

Бренд: TATA Motors Страницы: 232

Бренд: ideus Страницы: 116

Бренд: ROLEC Страницы: 2

Бренд: Van Guard Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды