Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1983

Страница: 1983 / 2589

1. Inner garnish (See

INNER GARNISH REMOVAL/INSTALLATION

2. Front door trim (See

FRONT DOOR TRIM REMOVAL/INSTALLATION

3. Front door speaker (See

FRONT DOOR SPEAKER REMOVAL/INSTALLATION

4. Front door glass (See

FRONT DOOR GLASS REMOVAL/INSTALLATION

5. Front door module (See

FRONT DOOR MODULE REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.

Fig. 20: Identifying Front Door Latch & Lock Actuator, Connector, Screws & Torque

Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION

1. The following actuators and switches are integrated with the front door latch and lock actuator. Inspect

the front door latch and lock actuator according to each inspection procedure for the following items.

Front door lock actuator (See

FRONT DOOR LOCK ACTUATOR INSPECTION

Front door key cylinder switch (Driver side) (See

FRONT DOOR KEY CYLINDER SWITCH

INSPECTION

Door lock-link switch (See

DOOR LOCK-LINK SWITCH INSPECTION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 13

«
...
1981
1982
1983
1984
1985
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды